Please note that this product is now obsolete and no longer sold. This product has been replaced by CDVI’s large-case PSUs.
The ievo enclosed PSU has been specifically designed to work with ievo biometric infrastructures, with room to feature both a suitable battery for backup and an ievo control board.
The non-intrusive unit is compliant with relevant European directives (CE) and standards.
Performing the simple function of storing an ievo biometric control board for remote ievo fingerprint reader devices, the enclosure can be easily installed/ mounted to walls or fascia for discrete positioning.
Please note, ievo control board and backup battery are not supplied as standard. Recommended battery – Yuasa NP7-12 (or similar).
Key Features:
High Quality & Reliability
IP64 Rated (using correctly rated cable glands)
Vandal resistant – IK07 (in-house certified)
Wide input voltage range (100-240 VAC)
Class I switch mode power supply
Built-in charging & battery protection circuit
Internally fused
Mains & battery charge level indicator
Isolate from front of enclosure
Small footprint & integrated rear mounting holes for simple installation
Simple hinged lid
2 years warranty
CE compliant
Technical Specifications:
Output | Output | Power | Charging |
DC Voltage | 13.8V | 13.8V | |
Rated Current | 2.8A | 1.5A | |
Current Range | 0 - 4.3A (Peak) | --- | |
Rated Power | 59.34W | ||
Ripple & Noise (Max) | 120mVp-p | --- | |
Voltage Adj. Range | 12 - 15V | --- | |
Voltage Tolerance | ±1.0% | --- | |
Line Regulation | ±0.5% | --- | |
Load Regulation | ±0.5% | --- | |
Set up, Rise Time | 800mS, 50mS/230VAC ~ 1600mS, 50mS/115VAC at full load | ||
Hold Up Time (Typ.) | 50mS/230VAC ~ 10mS/115VAC at full load | ||
Input | Voltage Range | 90 - 264VAC ~ 127 - 370 VDC | |
Frequency Range | 47-63Hz | ||
Efficient (Typ.) | 0.84% | ||
AC Current (Typ.) | 1.6A/115VAC ~ 1A/230VAC | ||
Inrush Current (Typ.) | Cold Start 30A/115VAC ~ 60A/230VAC | ||
Leakage Current | <1mA / 240VAC | ||
Protection | Overload | 105 - 150% rated output power | |
Protected type: Hiccup mode, recovers automatically after fault condition is removed | |||
Over Voltage | 14.49 - 18.63V | ||
Protection type: Hiccup mode, recovers automatically after fault condition is removed | |||
Battery Cut Off | 10.5±0.5V | ||
Function | AC OK | TTL open collector output ON: AC OK; OFF AC Fail; Ice: max. 30mA@50VDC |
|
Battery Low | TTL open collector output ON: Battery low; OFF: Battery OK; Ice: max. 30mA@50VDC |
||
Battery low voltage : <11V | |||
Environment | Working Temp. | Range = -20°C to +70°C | |
Working Humidity | Range = -20 to 90%RH non-condensing | ||
Storage Temp. Humidity | Range = -20°C to +85°C, 10 - 95%RH non-condensing | ||
Temp. Coefficient | ±0.03%/°C (0~50°C) on CH1 output | ||
Vibration | 10 - 500Hz, 2G 10min./1cycle, 60min. each along X,Y,Z axes | ||
Safety & EMC | Safety Standards | UL60950-1, TUV EN60950-1 approved, CE | |
Withstand Voltage | I/P-O/P:3KVAC I/P-FG:1.5KVAC O/P-FG:0.5KVAC | ||
Isolation Resistance | I/P-O/P, I/P-FG, O/P-FG:100M Ohms/500VDC/25°C/70%RH | ||
EMC Emission | Compliance to EN55022 (CISPR22) Class B, EN61000-3-2, -3 | ||
EMC Immunity | Compliance to EN61000-4-2,3,4,5,6,8,11, EN55024, light industry level, criteria A | ||
Dimensions | Width | 289mm | |
Height | 239mm | ||
Depth | 107mm |
Share this page:
[ninja_forms id=3018]